Tool-Co Grout & Binder

Tool-Co Grout & Binder

Tool-Co Grout & Binder is a polymer designer for filling pin holes and minor non-structural cracks in concrete. This is done during the grinding process before polishing concrete. Can be used as a binding agent on screeds and skim applications. For use on concrete surfaces.

Benefits
• Can be diluted up to 30% depending on the strength needed
• One step application, applied while doing the final stage of grinding
• Breathable and UV stable. Will not yellow, discolour, peel or flake.
• Non-flammable. Non-toxic. Low odour.
• Leaves a smoother uniform finish once applied.
• Drying time for foot traffic between 3-6 hours, full cure 72 hours

Instructions

DIRECTIONS FOR USE:

Polished Concrete

Remove all dust and debris using an auto-scrubbing machine. If surface has remaining contaminants, use an appropriate surface prep cleaner to remove any remaining surface contaminants which may compromise uniform application.

Allow wet surfaces to dry.

At the 120 grit metal or 50grit polish stage you must follow the following steps, Can be diluted up to 30%

  1. Floor must be clean and vacuumed.
  2. Dampen the surface with water before you apply. There must be no standing water.
  3. Apply Tool-co Grout by sprayer or block brush in front of the machine and grind into the floor using the 120# Metal or 50# Polish tool.
  4. Let it cure for 3 - 6 hours to get the best results.
  5. Remove excess grout off the surface using the same grit tool used to apply.
  6. Make sure floor is clean and vacuum and apply Tool-Co Lithium densifier.

Skim Coat applications 

Remove all dust and debris using an auto-scrubbing machine. If surface has remaining contaminants, use an appropriate surface prep cleaner to remove any remaining surface contaminants which may compromise uniform application.

Allow wet surfaces to dry.

  1. 25# Diamond Grind to remove all latency and debris
  2. Prime surface with undiluted Tool-Co Grout and Binder. Keep a wet edge.
  3. Mix 2 parts silica flour 325 mesh with 1 part 42.5N cement
  4. Add un-diluted Tool-Co Grout and Binder to dry mixture use a mechanical mixer until correct consistency.
  5. Apply by steel trowel to floor.

 MAINTENANCE:

Use normal dust mopping or sweeping between occasional detergent, Ameripolish rejuvenating cleaner and water cleaning.

Areas of use

Tool-Co Grout And binder is suitable for use in the following areas;

  • Polished Concrete floors
  • Warehouse floors
  • Shopping centres
  • Interior and exterior
  • Car Parks
  • Garages
  • Decorative floors
  • Concrete repairs

Substrate

Tool-Co Grout and Binder may be applied to new and existing concrete.

Coverage

Typical Coverage rates

Coverage rates are dependent upon the porosity of the concrete surface to be treated and are offered as a guide only. A sample test area is recommended to determine specific coverage rates.

 

Concrete Surface Coverage Rate (m2/L)
Freshly placed, uncured, steel trowelled 5-15
Cured, steel trowelled 5-15
Cured, ground/honed 5-10
Porous old concrete 2-10

Downloads

Technical Data Sheet

Safety Data Sheet

ImageCode Size Quantity
Tool-Co Grout & Binder - 1L LCH30001 1L
-
+
Tool-Co Grout & Binder - 5L LCH30005 5L
-
+
Tool-Co Grout & Binder - 25L LCH30025 25L
-
+
Tool-Co Grout & Binder - 200L LCH30200 200L
-
+
Tool-Co Grout & Binder - 1000L LCH31000 1000L
-
+

Follow MACTOOL on Social Media!

Find us

Head Office (Cape Town)

Unit 6 Pennisi Park, No.3 Jig Ave, Montague Gardens

Johannesburg

Unit 4 Hughes Industrial Park, Cnr Oscar & Romeo Rd, Hughes

Durban

Unit 1A, 44 Hillclimb Rd, Westmead

GET IN TOUCH

Head Office (Cape Town):

Email: sales@mactool.co.za
Tel: +27 21 552 8566

Johannesburg:

Email: salesjhb@mactool.co.za
Tel: +27 11 823 1077

Durban:

Email: saleskzn@mactool.co.za
Tel: +27 31 350 4004
linkedin facebook pinterest youtube rss twitter instagram facebook-blank rss-blank linkedin-blank pinterest youtube twitter instagram