Cape Town:+27 21 552 8566 Johannesburg:+27 11 823 1077 Durban:+27 31 350 4004
Mactool -

PRODUCTS

Bellinzoni Stone Products > Bellinzoni Cleaners


Bellinzoni Bert 27


Bellinzoni Bert 27
Bellinzoni Bert 27

Model: Bellinzoni Bert 27

Manufacturer: Bellinzoni


Bellinzoni Bert 27 detergent is a concentrated acid based detergent for granite, cement, porcelain, terracotta & unpolished stones. It also works against rust. It can be used for deep cleaning of very dirty floors, for cleaning mortar leftover after installation and for cleaning floors with grease and oil stains (factories, workshops etc …).


Bellinzoni Bert 27 is used on strong surfaces like Granite, Ceramic Porcelain and Cement floors with very resistant dirt. It reacts very well for the removal of degreasing oil residuals, salt efflorescence’s or superficial oxidation spot (rust on granite).

Dilute Bellinzoni Bert 27 in clean water, apply using a mop or pour it directly on the area to be treated. For floor application dilute 10/20 ml of Bellinzoni Bert 27 in one litre of water and apply using a mop, let it work for 5-10 minutes, rub with brush, abrasive pad or if available using a single disc machine (150-250 rpm) equipped with green or red abrasive disc type. The product can be used manually using a nylon brush, scrubbing brush or mop. Rinse with plenty of water. If dirt residual is still present, apply the product again. Rinse very well with water, brushing continuously. Remove residual using sponges, cloths, mop or vacuum. For vertical application use a brush and then rinse very well using a pressure washer.

 

Dilute the Bellinzoni Bert 27 in water depending on the amount of dirt to be removed. We suggest following dilution:

  • To clean cement, mortar, plaster etc… dilute 20/30 ml (2 table spoon) of Bellinzoni Bert 27 in 1 litre of warm water.
  • To clean rust, grease etc… dilute 50 ml (3-4 tablespoon) of Bellinzoni Bert 27 in 1 litre of warm water.
  • To clean residual efflorescence on granites and ceramic: dilute 30 ml (2 table spoon) in 1 litre of warm water.
  • Bellinzoni Bert 27 is acid based therefore we recommend rinsing all tools used for the job very well, especially the vacuum unit or single disc machine.
  • We suggest not using Bellinzoni Bert 27 on polished marble, on terrazzo, on calcareous stones, on slates and any material sensitive to acids.
  • Before use read the recommendations printed on the tin.

 

 

Floors: 150/200 m2 with 1 litre. Coverage depends on the quality and intensity of dirt to be removed.
For rust, coverage depends of the deepness of the rust, if it is superficial rust it is possible to clean 30/40 m2.
If it is resistant rust it may be necessary to do a double application. In the extreme case of very resistant rust in the stone it may be necessary to use the product Bellinzoni Rust Remover.


Code Description Unit Add to Enquiries
GB06001 Bellinzoni Bert 27 1lt Extra Strong Detergent 1LT

Bellinzoni Hygienix Detergent


Bellinzoni Hygienix Detergent
Bellinzoni Hygienix Detergent

Model: Bellinzoni Hygienix Detergent

Manufacturer: Bellinzoni Italy


Bellinzoni Hygienix Detergent is a detergent with hygienic, deodorizing and strong degreasing action for the deep sanitation of public and private areas, such as schools, hospitals, offices, public toilets and in particular: table tops, bathroom floors and tops, eating houses, cooking tools. Bellinzoni Hygienix Detergent reduces the bacterial charge of an area. Bellinzoni Hygienix Detergent can be used as multipurpose cleaner.


 

Where to apply:

Marble, Granite, Ceramic, terrazzo, cement, terracotta and any most other surfaces.

Very good for cleaning kitchens and sanitary areas.

 

Usage:

Use Bellinzoni Hygienix Detergent to hygienically clean and deodorize kitchens, tables, countertops. Hygienix Detergent can be used undiluted when a deep clean is required i.e. public areas. Bellinzoni Hygienix Detergent can also be used for regular cleaning of surfaces.

 

Dilute 20/30 ml of Bellinzoni Hygienix Detergent in 1 litre of warm water. For deep cleaning use a higher concentration of Bellinzoni Hygienix Detergent.

Apply with a sponge, cloth or mop.

 

Coverage:

1 litre can clean up to 100-120 m2 depending on the dilution and the condition of the floor.

 

For more details regarding tests and certificates please view the Bellinzoni Hygienix Detergent Technical PDF.

Product Documentation:

Hygienix Detergent Technical.pdf


Code Description Unit Add to Enquiries
GB08201 Bellinzoni Hygienix Detergent 1lt 1LT

Bellinzoni Rust Cleaner Gel


Bellinzoni Rust Cleaner Gel
Bellinzoni Rust Cleaner Gel

Model: Bellinzoni Rust Cleaner Gel

Manufacturer: Bellinzoni Italy


Bellinzoni  "MangiaRuggine" (“RustEater”) is a gel product, especially formulated for the elimination of rust stains on all natural stone materials such as marbles, granites, calcareous stones, slate, terracotta and ceramics. It does not contain acids so, unlike other similar products, it can be safely used on polished marbles, without ruining the shine. The “RustEater” Gel acts quickly and it removes rust without effort.


 

Instruction for Use:

Wet the surface in advance with clean water. Then apply a 5 mm thick layer of Bellinzoni “RustEater” on the stain, using a spatula or similar tool. Once the product has been evenly distributed on the stain let Bellinzoni “RustEater” work, it will turn its original semi-transparent yellow-orange colour into opaque dark violet. This colouring shows that the necessary reaction for rust removal has correctly occurred.

The time it takes to activate can vary considerably, depending on the material on which it is applied and surface finish aspect. In general, on materials with polished finish it is necessary to wait longer. In any case, it is suggested to perform preliminary tests to determine activation time.

Once the reaction has happened, it is suggested to not leave the Bellinzoni “RustEater” on treated material for longer than 10 minutes; this is to avoid that the reacted “RustEater” residue could penetrate in the material. Rinse with lots of water and repeat the application if necessary.

 

Suggestion for Use:

  • In case that, after first application, the stain is not completely disappeared, proceed to further applications.
  • Read the recommendations printed on label before use carefully.
  • Always perform a test before use.

 

Application on surfaces:

Marbles, granites, terracotta, porphyry, cement, slate, concrete, ceramics, grès.

 

Coverage:

Coverage is subject to the intensity of the stain. Bellinzoni “RustEater” should be applied only on small surfaces where there is particular stain.

Product Documentation:

Rust Cleaner Gel Technical.pdf


Code Description Unit Add to Enquiries
GB06901 Bellinzoni Rust Cleaner Gel 1lt 1LT

Bellinzoni Mess Muncher Absorbing Paste


Bellinzoni Mess Muncher Absorbing Paste
Bellinzoni Mess Muncher Absorbing Paste

Model: Bellinzoni Mess Muncher Absorbing Paste

Manufacturer: Bellinzoni Italy


Bellinzoni Mess Muncher Absorbing Paste for stubborn dirt removal is a product specifically formulated to remove stain on marble, granite, ceramic and concrete.

It eliminates most of the visible stains such as industrial oil, edible oil, coffee etc..

It doesn’t change the look of the stone or leave different shades and allows you to reinstate the stone original beauty. The chemical composition of the paste allows deep stubborn stains to be absorbed.


 

Method of use

Apply a layer of approx. 5mm on the area to be treated. We suggest applying it with a spatula. Cover with plastic film (polyethylene) to create humidity so that the paste remains moist and the dirt absorption will be more efficient. After 2-3 hours remove the plastic film and let the paste dry out normally. After 8-10 hours depending on room temperature the paste will appear like dry whitish mud and can be removed with a brush.

 

Remarks and suggestions

Mix the paste well in its container before applying. The paste must be sticky to maximise its efficiency. When applied to oily stains make sure the paste is well applied. If after the first application the stain is not completely removed repeat the procedure above. Once the dried paste is removed, wash with detergent Bellinzoni LEM-3. To avoid further staining we recommend protecting the stone with a water and oil repellent Bellinzoni Block D70.

 

Coverage:

Much depends on the stain intensity, bear in mind that the product is used to remove special stains and should be applied on specific areas. In case of wide spread stains we recommend using liquid detergents.

Product Documentation:

Mess Muncher Absorbing Paste Technical.pdf


Code Description Unit Add to Enquiries
GB06601 Bellinzoni Mess Muncher Absorbing Paste 250ml 250ml
GB06602 Bellinzoni Mess Muncher Absorbing Paste 1kg 1KG
GB06603 Bellinzoni Mess Muncher Absorbing Paste 5kg 5KG

Bellinzoni Lem-3


Bellinzoni Lem-3
Bellinzoni Lem-3

Model: Bellinzoni Lem-3

Manufacturer: Bellinzoni Italy


Bellinzoni Lem-3 is concentrated detergent to clean all surfaces especially suited for the treatment of marble, granite and natural stones. Designed for resistant dirt. Can be used to clean and wash all cleanable surfaces (example glass).


 

Instruction for Use:

For manual floor application dilute 30-50 ml (2-3 tablespoon) of product directly in a bucket of water, mix well and then clean the surface using a scrubbing brush with soft cloth. Once floor is clean, let it dry. For big areas dilute the product directly in tank of the single disc polish machine equipped with green cleaning pad and proceed in cleaning the floor. If available use a vacuum to clean the dirty water. This process avoid that dirty water could enter into stone porosity. For very resistant soil repeat the application or use a stronger product (suggested our Bellinzoni Cleaner Ultra Stripper). Let the floor dry before walking on it.

 

Suggestion for Use:

  • Depending on the dirt that needs to be removed. We suggest following dilution:
    • Periodic maintenance of marble or granite floors: Dilute 30-50 ml (2-3 tablespoon) of Bellinzoni Lem-3 in 1 litre of warm water.
    • For removal of heavy dirt or grease spots, increase dilution to 100 ml (6-7 tablespoon) of Bellinzoni Lem-3 in 1 litre of warm water.
  • Before use, read recommendations printed on the tin carefully.

 

 

Application on surfaces:

All surfaces types, especially studied for marbles, granites, stone, terrazzo, agglomerated and engineered stone.

 

Coverage:

To wash stone floors it is possible to treat 150/200 m2 with 1 litre of product. Coverage of product depends on the quality and intensity of dirt that needs to be removed.

Product Documentation:

Hygienix Lem-3 Technical.pdf


Code Description Unit Add to Enquiries
GB06201 Bellinzoni Lem-3 1lt 1LT

Bellinzoni Ultrastripper Concentrate Cleaner


Bellinzoni Ultrastripper Concentrate Cleaner
Bellinzoni Ultrastripper Concentrate Cleaner

Model: Bellinzoni Ultrastripper Concentrate Cleaner

Manufacturer: Bellinzoni Italy


Highly efficient detergent for every type of dirt: grease, smog, oily stains. It removes very resistant metallic, acrylic and solvent based waxes from floor and wall and it is also suitable for deep cleaning of floors before polishing.

It is also very useful for cleaning tile joints and gaps.


 

Instruction for Use:

Dilute 10 – 15% of the product in water; apply with a mop/brush or for big areas by floor polisher equipped with cleaning pad or carbon brush. If some residue is still left, repeat the operation.

Rinse the floor thoroughly with clean water to avoid drying dirt settling again in the joints and gaps. If possible remove the water with the vacuum.

For application on vertical surfaces (indoor or outdoor wall claddings, columns, statues etc), use a brush or an abrasive pad. Else you can use “ULTRASTRIPPER GEL”. Spread the product and then rub hard with the pad or brush over the same surface. Rinse well.

 

Suggestion for Use:

  • Premix the product in the floor scrubbing machine tank.
  • In case of stubborn dirt, increase the product concentration depending on the requirement.
  • Recommend to use ULTRA STRIPPER for deep cleaning of the floors prior crystallisation or to clean places with very stubborn dirt such as car workshop, showrooms, parking lots and industrial floors etc.
  • Recommend using lukewarm water.
  • Read recommendations printed on the tin before use carefully.

 

Application on surfaces:

Marble, granite, terrazzo, porcelain homogenous tiles, glazed tiles.

 

Coverage:

To clean stone or cement surfaces with 1 litre of product it is possible to treat 80 to 120 m2.

Output varies depending on quantity used and type of dirt to remove.

 

Product Documentation:

Ultrastripper Concentrate Cleaner Technical.pdf


Code Description Unit Add to Enquiries
GB06102 Bellinzoni Bellinzoni Ultrastripper Concentrate Cleaner 5LT

Algae Remover Algakill


[CAPTION]

Manufacturer: Bellinzoni Italy


Algae Remover Algakill is a concentrated product with strong hygienic action. It removes and prevents deposits of Alga, moulds and musk. Suitable for slabs, facades and swimming pools. The product can be used as an alga and musk remove as well as a preventer

 


 

Instruction for Use:

Liquid Version:

  • Lay the product on the surface to be cleaned using a waterjet machine or by brush.
  • Algakill can be used pure or diluted with water up to 1:3. Using warm water gives better results.
  • Let Agakill work for 30-60minutes and rinse with water.

 

 Spray Version:

  • Spray evenly on the surface to clean specially on the part where there is presence of algae, mildew and humidity spots.
  • Let Algaekill work for 30-60 minutes (mildew and algae will change colour in light and become grey. Rinse with water brushing and making abrasive action in order to remove the dust
  • To clean humidity spot on plaster it is suggested that you brush without water.
  • No dilution is need. The product is ready to use,

Algae prevention in swimming pools and fountains:

  • Drop Algaekill directly into the water or into the skimmer.
  • Follow the following dilution.
    • First Dosage – 40gr/m3 of water.
    • Maintenance Dosage 20gr/m3 of water once a week.
    • Concentrated Dosage 70gr/ m3 of water.

 

 

Suggestion for Use:

  • When Algaekill is used as a remover we suggest scrubbing the area first with a brush without water to remove part of the impurities. Brush can be used dry without water or chemicals.
  • In order to maintain the material clean from algae and musk, repeat treatment every 6 months. Normally it is recommended to make the treatment in autumn and spring.
  • When Algakill is used for prevention in swimming pools, fountains etc… we recommend not exceeding the suggested ratio.

 

Application on surfaces:

Marble, granite, ceramic, terrazzo, cement, terracotta and any cleaning surface.

 

Coverage:

Clean stones in general and cements: With 1 litre of Algakill it is possible to clean 20-30m2. If the stone is covered by impurities, algae, mildew and musk, then it is possible to clean 10-15m2

Product Documentation:

Algae Remover Algakill Technical.pdf


Code Description Unit Add to Enquiries
GB05701 Algae Remover Algakill 1lt 1LT