Cape Town:+27 21 552 8566 Johannesburg:+27 11 823 1077 Durban:+27 31 350 4004
Mactool -

PRODUCTS

Bellinzoni Stone Products > Protective Sealers


Bellinzoni Idea HP Water & Oil Repellent


Bellinzoni Idea HP Water & Oil Repellent
Bellinzoni Idea HP Water & Oil Repellent

Model: Bellinzoni Idea HP Water & Oil Repellent

Manufacturer: Bellinzoni Italy


Clear protective agent to protect stones against water, oil, grease and humidity. Bellinzoni IDEA HP penetrates deep into the stone, blocking the efflorescence and lets the stone breath.

Bellinzoni IDEA HP does not change the natural colour of the stone and does not create an unsightly plastic film.

 

Laboratory test shows Bellinzoni IDEA HP resists well to UV rays and the colour does not change even after prolonged time. Bellinzoni IDEA HP is perfectly clear and leaves the original stone colour unaltered. Most suitable for façade, table, kitchen, vanity tops etc. It prevents mildew formation



Where to Apply

Marble, granite, stone, cement and artificial Stone

Application

Clean and dry the surface that is to be treated well. Apply IDEA HP evenly with a cloth, brush or other proper tool which can remove any excess. When the stone is porous a second coat may be necessary after 2 hours.  To remove excess, rub the area with a cloth soaked with IDEA HP within 2 hours of the last application

Yield

Approximately 10m2 per 1 litre when applied on a polished surface.


Code Description Unit Add to Enquiries
GB01502 Bellinzoni Idea HP 1lt Water & Oil Repellent 1LT
GB01503 Bellinzoni Idea HP 5lt Water & Oil Repellent 5LT
GB01504 Bellinzoni Idea HP 25lt Water & Oil Repellent 25LT

Bellinzoni Idea XC Water & Oil Repellent (Wet Look)


Bellinzoni Idea XC Water & Oil Repellent (Wet Look)
Bellinzoni Idea XC Water & Oil Repellent (Wet Look)

Model: Bellinzoni Idea XC Water & Oil Repellent (Wet Look)

Manufacturer: Bellinzoni Italy


Bellinzoni IDEA XC is a new impregnating sealer to protect stones against water, oil, grease and humidity giving an attractive wet-look effect; optimum also for polished materials. When applied, Bellinzoni IDEA XC penetrates into the stone without forming unsightly plastic films.

Bellinzoni IDEA XC will make the stone water and oil repellent by penetrating deeply into the stone, protecting it from water and oily substances but allowing the stone to breath while the humidity can evaporate, therefore blocking efflorescence. The constant research for latest generation raw materials has permitted us to produce new water and oil repellent, which can enhance the colour of stone and at the same time, it can protect from stains caused by oil and other penetrating substances.



Where to Apply

Marble, granite, stone, cement and artificial Stone

Application

Clean and dry the surface that is to be treated well. Apply IDEA XC evenly with a cloth, brush or other proper tool which can remove any excess. When the stone is porous a second coat may be necessary after 2 hours.  To remove excess, rub the area with a cloth soaked with IDEA XC within 2 hours of the last application

Yield

Approximately 10-25m2 per 1 litre when applied on a polished surface.


Code Description Unit Add to Enquiries
GB01602 Bellinzoni Idea XC 1lt Water & Oil Repellent 1LT

Bellinzoni Idea Gold 1lt Water & Oil Repellent


Repellent Idea Gold 1lt Water & Oil Repellent
Repellent Idea Gold 1lt Water & Oil Repellent

Model: Bellinzoni IDEA GOLD Water & Oil Repellent

Manufacturer: Bellinzoni Italy


Bellinzoni IDEA GOLD is an exceptional anti-stain product based on nanotechnology formulation; it protects marble and granite stones from a wide range of stains and has prolonged efficacy.

Bellinzoni IDEA GOLD is a transparent protective used for maximum protection of all stone surfaces against water penetration, oil, fats and moisture. Bellinzoni IDEA GOLD works great even on shiny materials, allows the stone to breathe, blocks efflorescence, penetrates deep, does not alter the natural colour of treated surface and does not create any film.

Bellinzoni IDEA GOLD has a spectacular "pearl effect": water droplets on treated surface take shape of spheres, which glide away.
Laboratory tests demonstrate the UV resistance of product, which has no color change even after prolonged exposure. It is perfectly invisible and leaves the original color of material unchanged. It prevents formation of mold.


 

 

Application on surfaces:

Marble, granite, terrazzo, agglomerated and engineered stones, sandstone, limestone, concrete.

Restoration and enhancement works, on inside and outside stone or masonry surfaces.

Ideal for protecting walls, brick or concrete walls, stone floors (matte or glossy marble or granite).

 

Instruction for Use:

Surface must be clean and dry; stains, mildew, crusting must be scraped off otherwise they will be harder to remove after protection. Application can be done by brush, cloth, roller or fleece. It is suggested, when possible, to apply the product by brush because it allows the product to penetrate well into the stone.

Application of IDEA GOLD by brush will facilitate penetration into frames and cavities. Let the product dry naturally and the stone will be protected.

On low absorbing surfaces, apply IDEA GOLD and, after some minutes, remove the excess of product using a dry and clean microfiber cloth.

 

Suggestion for Use:

  • Apply IDEA GOLD twice, waiting 1 hour after the first application.
  • It is suggested to apply the product till the complete saturation of the stone.
  • Do not dilute the product with any solvent or water, formulation is ready for use
  • Material has to be completely dry before treatment.
  • Do not let the excess IDEA GOLD dry on the surface: in case of excess application, remove it with a cotton or microfiber cloth.
  • Protect from rain or humidity for first few hours after application.
  • In case the application of IDEA GOLD is subjected to foot traffic, in case of icing temperatures pay attention to pearl effect that could turn the surfaces slippery. It is then suggested to apply product at least 60 days before forecasted icing temperatures.
  • For small pieces of stone it is possible to apply the product by immersion
  • Once the material has been treated it is necessary to wait 24 hours for complete polymerization.
  • In case of treatment of statues, decorations etc. pay attention to all cavities and corners.
  • Read recommendations printed on the tin before use carefully.

 

Coverage:

For protection of marble and granite polished after grit 800, with 1 litre of product is possible to treat 15/30 m2. In case of not polished marble or granite, calcareous stone, limestone, sandstone, concrete with 1 litre of product, it is possible to treat 8/15 m2.

 

 

 

 

 

 

Product Documentation:

Idea Gold Technical.pdf


Code Description Unit Add to Enquiries
GB01802 Bellinzoni Idea Gold 1lt Water & Oil Repellent 1LT
GB01803 Bellinzoni Idea Gold 5lt Water & Oil Repellent 5LT

Bellinzoni Idea Dark Water & Oil Repellent


Bellinzoni Idea Dark Water & Oil Repellent
Bellinzoni Idea Dark Water & Oil Repellent

Model: Bellinzoni Idea Dark Water & Oil Repellent

Manufacturer: Bellinzoni Italy


Bellinzoni  IDEA DARK is a protective impregnating agent, for the treatment of both shiny and rough surfaces of natural stones such as granites, marbles, etc. Specific for dark or black absorbing stones, Bellinzoni  IDEA DARK deeply enhances the natural colour of stone, covers scratches and flaws of dark/black stone.




Application on surfaces:

Marble, granite, terrazzo, agglomerated and engineered stones, sandstone, limestone, concrete.

Restoration and enhancement works, on inside and outside stone or masonry surfaces.

Ideal for protecting walls, brick or concrete walls, stone floors (matte or glossy marble or granite).

 

Instruction for Use:

Surface must be clean, dry, without any trace of dirt; stone to be treated must not contain salts (sulfates, chlorides and nitrates) since their presence reduces the absorption. Stains, mildew, crusting must be scraped off otherwise they will be harder to remove after protection. Apply IDEA DARK without any dilution, using a brush, a cloth, by roller or by spray gun. It is suggested, when possible, to apply the product by brush because it allows the product to penetrate well into the stone. In this case, apply IDEA DARK making a gentle pressure on the brush, in order to facilitate penetration into frames and cavities. Apply necessary quantity up to complete absorption. After 10/15 minutes, remove excess of product with an absorbing cloth

 

Suggestion for Use:

  • It is advisable to apply the product until complete saturation of the stone.
  • On very absorbent material it is better to make a second application after one hour.
  • Do not dilute the product with any solvent or water, formulation is ready for use.
  • Material has to be completely dry before treatment.
  • For small pieces of stone it is possible to apply the product by immersion.
  • Once the material has been treated it is necessary to wait 24 hours for complete polymerization.
  • In case of treatment of statues, decorations etc. Pay attention to protect all cavities and corners.
  • Read carefully recommendations printed on the tin before use.

 

 

Coverage:

For protection of marble and granite polished after grit 800. With 1 litre of product it is possible to treat 15/20 m2. In case of calcareous stone, limestone, sand stone, polished or grinded concrete with the same finish, yield could be slightly less. Treatment of absorbing stones, or with a rough finish, could require a higher amount of product, with an indicative coverage of 10 m2 with 1 litre.

 

 

 

Product Documentation:

Idea Dark Technical.pdf


Code Description Unit Add to Enquiries
GB01702 Bellinzoni Idea Dark 1lt Water Repellent 1LT
GB01703 Bellinzoni Idea Dark 5lt Water Repellent 5LT
GB01704 Bellinzoni Idea Dark 25lt Water Repellent 25LT

Bellinzoni Idea Black 750ml Water Repellent


Bellinzoni Idea Black 750ml Water Repellent
Bellinzoni Idea Black 750ml Water Repellent

Model: Bellinzoni Idea Black 750ml Water Repellent

Manufacturer: Bellinzoni Italy


Description:

Bellinzoni IDEA BLACK is the new silicone-based protective impregnating agent, dyed in intense black colour for the treatment of black granites and stones. Great for enhancing black polished granites, that usually cannot be easily enhanced with other products.

It penetrates easily without forming a film on surface, and ages well inside and outside.

Bellinzoni IDEA BLACK is UV stable, anti-adhesive and anti-static and remains clean over time.

Bellinzoni IDEA BLACK intensifies the black colour of stone, allows hiding of scratches, defects and imperfections of black stones.


 

Instruction for Use:

Surface preparation: The surface must be clean, dry and free of waxes.

IDEA BLACK can be applied by brush or spray at low pressure in one or more coats, depending on absorption of material to be treated. The product applies its full effect after at least 6 hours from application.

 

Suggestion for Use:

  • Do not dilute the product with any solvent or water, formulation is ready for use.
  • Material has to be completely dry before treatment.
  • For small pieces of stone it is possible to apply the product by immersion
  • Once the material has been treated it is necessary to wait at least 6 hours for complete polymerization.
  • For cleaning, use neutral cleaners only i.e. Bellinzoni LEM-3 DETERGENT.
  • Do not use the product at temperatures below 5°C
  • If the product has been stocked at low temperatures for long time, it is suggested to bring it back to 20°C before usage.
  • Work in a well ventilated area, or provide adequate ventilation
  • Read the recommendations printed on the tin before use carefully.

 

Application on surfaces:

Black granites and stones

 

Coverage:

Depending on degree of polishing material, and desired intensity of black.

 

 

Product Documentation:

Idea Black Technical.pdf


Code Description Unit Add to Enquiries
GB01902 Bellinzoni Idea Black 750ml Water Repellent 750ml

Bellinzoni Strong 2000 Consolidator 1lt


Bellinzoni Strong 2000 Consolidator 1lt
Bellinzoni Strong 2000 Consolidator 1lt

Model: Bellinzoni Strong 2000 Consolidator 1lt

Manufacturer: Bellinzoni Italy


Bellinzoni Strong 2000 is a clear siloxane consolidating agent for protection of buildings and stones against penetration of water, grease and humidity.
Bellinzoni Strong 2000 is best used on polished material. It lets the stone breath and does not allow the efflorescence to exit from the stone. Bellinzoni Strong 2000 penetrates deeply into the stone and does not change the original colour of the treated stone, does not make any film but catalyses into the stone giving an excellent protection. Tests carried out in the laboratories demonstrate resistance to UV rays. The stone treated does not change colour after prolonged exposure to UV.  Bellinzoni Strong 2000 is perfectly invisible and does not give a wet look or shine to the treated material, but maintains the original aspect of the stone. It prevents the formation of mildew.


 

Instruction for use:

Surface must be clean and dry. Stains, mildew and crusting must be scraped off otherwise they will be harder to remove after protection. Application can be done by brush, by roller or by spray gun. It is suggested, when possible, to apply the product by brush because it allows the product to penetrate better into the stone. Application of Strong 2000 by brush will facilitate penetration into frames and cavities. Repeat the application continuously without interruption until the stone has been saturated (the stone does not absorb further product). Let the product dry naturally and the stone will be protected. In case of excess product, remove excess using a cloth saturated in strong 2000.

 

 Suggestion for Use:

  • Material has to be completely dry before treatment.
  • Do not dilute the product with any solvent or water, formulation is ready for use.
  • It is recommended to apply the product until the stone is completely saturated without waiting between applications. Do not let the product dry during application until complete saturation.
  • Once the material has been treated it is necessary to wait 24 hours for complete polymerization.
  • For small pieces of stone it is possible to apply the product by immersion
  • In case of treatment of statues, decorations etc. pay attention to all cavities and corners.
  • Read recommendations printed on the tin before use carefully.
  • Always carry out a test before effective use.

 

Application on surfaces:

Marble. Granite, terrazzo, Agglomerated and engineered stones, sandstone, limestone and concrete

Product Documentation:

Strong 2000 Technical.pdf


Code Description Unit Add to Enquiries
GB02101 Bellinzoni Strong 2000 Consolidator 1lt 1LT

Bellinzoni Block D70 Water & Oil Repellent


Bellinzoni Block D70 1lt Water & Oil Repellent
Bellinzoni Block D70 1lt Water & Oil Repellent

Model: Bellinzoni Block D70 Water & Oil Repellent

Manufacturer: Bellinzoni Italy


Description:

Bellinzoni Block D70 is a colourless water and oil repellent for protection of stone facade, floors and stone products against penetration of water, humidity, oil, alimentary grease. It prevents mildew formation. Its chemical composition allows the treated material to breathe and allows humidity to exit from the stone but prevent the same from entering. Bellinzoni Block D70 is for internal and external use.  

Bellinzoni Block D70 is water-based, and therefore non-inflammable and non-toxic.


Instruction for Use:

Surface must be clean and dry. Stains, mildew and crusting must be scraped off otherwise they will be harder to remove after protection. Lay the product evenly on the surface to be protected, making the stone completely damp, wait 3-5 minutes and remove the excess with a cloth. Let it dry and the result will be a protected material. It is possible to dilute Block D70 up to 50% with water to have a better absorption depending of material to be treated.

 

Suggestion for Use:

  • On very absorbent material it is better to make a second application 30 minutes after the first application.
  • For protection of polished material like marble & granite we suggest to dilute the product 50% with water.
  • Material has to be completely dry before application.
  • For small pieces of stone it is possible to treat it by immersion and it is also possible to use a sponge damp with BLOCK D70 and apply it on the material.
  • Once treated the material has to dry for 24 hours until the polymerization of the chemical is complete.
  • In case of treatment of statues, decorations etc. pay attention to reach all the cavities and corners.
  • Do not let the product dry naturally without removing the excess after 3-5 minutes.
  • Read recommendations printed on the tin before use carefully.

 

Application on surfaces:

Marble, granite, terrazzo, engineered stones, sandstone, limestone, concrete

 

Coverage:

For protection of marble and granite polished or grinded after grit 800, with 1 litre of product is possible to treat 30/40 m2. In case of calcareous stone, limestone, sand stone, concrete polished or grinded after grit 800 with 1 litre of product, it is possible to treat 10/15 m2.

 

Product Documentation:

Block D70 Technical.pdf


Code Description Unit Add to Enquiries
GB02302 Bellinzoni Block D70 1lt Water & Oil Repellent 1LT
GB02303 Bellinzoni Block D70 5lt Water & Oil Repellent 5LT
GB02304 Bellinzoni Block D70 25lt Water & Oil Repellent 25LT

Bellinzoni Limeseal Water & Oil Repellent


[CAPTION]

Model: Bellinzoni Limeseal Water & Oil Repellent

Manufacturer: Bellinzoni Italy


Description:

Bellinzoni Limeseal is a colourless impregnating and anti-salts resurfacing product, that also protects the material from water and oil. Bellinzoni LIMESEALER is suited for very porous and friable stones such as limestone and sandstone. Bellinzoni LIMESEALER gives a high protection against penetration of water, humidity and against action of acid rains. It prevents formation of mildews on material exposed to humidity and blocks the resurfacing of salts. Bellinzoni LIMESEALER is in most of cases transparent and does not give a wet or shiny aspect to the treated material.


Instruction for Use:

Surface must be clean and dry. Stains, mildew and crusting must be scraped off otherwise they will be harder to remove after protection. Application can be done by brush, by roller or by spray gun. It is suggested, when possible, to apply the product by brush because it allows the product to penetrate better into the stone. Application of LIMESEALER by brush will facilitate penetration into frames and cavities. Repeat the application continuously without interruption until the stone has been saturated (the stone does not absorb further product).

 

 Suggestion for Use:

  • Material has to be completely dry before treatment.
  • Do not dilute the product with any solvent or water, formulation is ready for use.
  • It is recommended to apply the product until the stone is completely saturated without waiting between applications. Do not let the product dry during application until complete saturation.
  • Once the material has been treated it is necessary to wait 24 hours for complete polymerization.
  • In case of treatment of statues, decorations etc. pay attention to all cavities and corners.
  • Read recommendations printed on the tin before use carefully.
  • Always carry out a test before effective use.

 

Application on surfaces:

Sandstone, Limestone, and all porous and friable materials.

Product Documentation:

Lime Seal Technical.pdf


Code Description Unit Add to Enquiries
GB02001 Bellinzoni Limeseal 1lt Water & Oil Repellent 1LT

Bellinzoni Grezzo Enhancer


Bellinzoni Grezzo Enhancer
Bellinzoni Grezzo Enhancer

Model: Bellinzoni Grezzo Enhancer

Manufacturer: Bellinzoni Italy


Description:

Bellinzoni GREZZO is a deep colour enhancing and protective agent, used to intensely increase colour of material. It also raises resistance against penetration of water and oils, on surfaces and handmade objects with rough finish. It lets the stone breath; it penetrates deeply, enhancing the colour of the stone and gives an attractive and deep wet look. Bellinzoni GREZZO does not make any film.

 


 

Instruction for Use:

Surface must be clean and dry. Stains, mildew and crusting must be scraped off otherwise they will be harder to remove after protection. Application can be done by brush, by roller or appropriate tool. It is suggested to apply the product by brush because it allows the product to penetrate better into the stone. Application of Bellinzoni  GREZZO by brush will facilitate penetration into frames and cavities. 30 minutes after application rub with a clean cloth to remove excess of product.

 

Suggestion for Use:

  • On very absorbent material, or to further enhance colour of treated material, it is possible to make a second cross-handed application after three hours
  • Do not dilute the product with any solvent or water, formulation is ready for use
  • Material has to be completely dry before treatment.
  • Once the material has been treated it is necessary to wait 24 hours for complete polymerization.
  • In case of treatment of statues, decorations etc. pay attention to reach all the cavities and corners.
  • Read recommendations printed on the tin before use carefully.
  • Always test before application.
  • For internal use.

 

Application on surfaces:

Marble, granite, calcareous stones with flamed, semi-polished, lapped or rough finish.

 

Coverage: With 1 litre of product, it is possible to treat up to 10m2, depending on material finish and porosity.

Product Documentation:

Grezzo Technical.pdf


Code Description Unit Add to Enquiries
GB06701 Bellinzoni Grezzo Enhancer 1lt 1lt
GB06702 Bellinzoni Grezzo Enhancer 5lt 5lt