Cape Town:+27 21 552 8566 Johannesburg:+27 11 823 1077 Durban:+27 31 350 4004
Mactool -

PRODUCTS

Bellinzoni Stone Products > Bellinzoni Polishers


Bellinzoni RR/1 Spray


Bellinzoni RR/1 Spray
Bellinzoni RR/1 Spray

Model: Bellinzoni RR/1 Spray

Manufacturer: Bellinzoni


One of the most popular requests for the maintenance of marble, granite and varnished wood is for a product which cleans and polishes in one operation. Bellinzoni RR/1 SPRAY is a foam product specifically for cleaning and polishing with wax to increases the shine and life. 

It does not contain CFC and therefore does not endanger the ozone layer.


Bellinzoni RR/1 SPRAY must be sprayed on the surface to be treated at a 5-10cm distance, spread with a dry soft cloth the lightly rubbed. Let it penetrate for 3-5min andthen polish using a wool or clean cotton cloth.

  • Do not exceed the recommend use because an excess of the spray could make the polishing operation more difficult and could leave shadow.
  • Follow the instruction on the tin carefully

Applications:
Marble, Granite, engineered Stone, resin Marble and most natural stones.


Code Description Unit Add to Enquiries
GB04901 Bellinzoni RR/1 Spray Polish 400ml 400ml Tin

Bellinzoni Wax Paste for Polishing


Bellinzoni Wax Paste for Polishing
Bellinzoni Wax Paste for Polishing

Model: Bellinzoni Wax Paste for Polishing

Manufacturer: Bellinzoni Italy


Bellinzoni Wax Paste for special preparation for polishing marble and granite:

This product comes in a paste form for polishing marbles, granites and cements. It dries quickly and forms a film of top quality waxes on the surface which penetrate into the material. It gives long lasting sheen. It is a top quality concentrated wax, dissolved in a non-inflammable solvent. This is a paste with exceptional polishing and protective power, due to the extremely high quality of raw materials used in its preparation. The product penetrates into the material and if it is then rubbed with fine steel wool, a felt pad, a dry woollen or cotton cloth, a uniform brilliant and long lasting mirror-finish will be achieved. Owing to its special composition this product fills and seals porosities in the material and covers small scratches. It is available in the following colours: White & Black


 

Instructions for use:

Apply evenly on the surface until all porosities are saturated, can be polished using bristle brush. Can be diluted with turpentine to delay drying

 

Application on surfaces:

Marble, granite, travertine, slate tiles and agglomerate natural stones

 

Yield:

With 1 kg of product can treat 15 – 20 m2 of compact material

 

Suggested use:

House, industry and big areas

Product Documentation:

Wax Paste for Polishing Technical.pdf


Code Description Unit Add to Enquiries
GB00102 Bellinzoni Wax Paste for Polishing White 930ml 930ml
GB00202 Bellinzoni Wax Paste for Polishing Black 930ml 930ml

Bellinzoni Special Liquid Wax for Polishing


Bellinzoni Special Liquid Wax for Polishing
Bellinzoni Special Liquid Wax for Polishing

Model: Bellinzoni Special Liquid Wax for Polishing

Manufacturer: Bellinzoni Italy


Bellinzoni Liquid prepartion for polishing corners and edges

 

Liquid wax specially formulated to intensify and to enhance marble and granite colours giving them an attractive “wet look”. Since the product contains no resins, it will not leave an unattractive film and will not become yellow. It dries quickly and polishes easily. Bellinzoni liquid preparation is exceptionally useful for corners, edges and areas where mechanical polishing is difficult.

 


 

Instructions for use:

Apply evenly on the surface to treat (surface has to be clean and without powder). Let it dry for 5-10 minutes (Depending on temperature). To reach a very brilliant result it is necessary to buff with a dry cloth, with fine steel wool (00 or 000) or by brush. It is also possible to polish the stone using an electric machine (Max 2000RPM) equipped with a felt disc or cloth disc. If the product is applied to the floor it can be polished using a single disc polish machine with steel wool.

 

Suggestion for use:

  • To facilitate penetration of the wax into the material we suggest warming the slab, this procedure will open the porosities, letting the wax penetrate deeply.
  • To delay dry time of the wax dilute the product 30% with turpentine.
  • Do not apply on synthetic materials. (Plastic, rubber, linoleum etc…)
  • Before use read the recommendations printed on the tin carefully.

 

Application on surfaces:

Marble, granite, travertine, slate tiles and agglomerate natural stones

 

Yield:

For polishing of marble and granite polished greater than 800# grit and with 1 kg of wax it is possible to treat 20-30 m2. In case of calcareous stone, limestone, sans stone, polished concrete with grit higher than 800# it is possible to treat 15-25m2

 

Suggested use:

House, industry and big areas

Product Documentation:

Special Liquid for Polishing Technical.pdf


Code Description Unit Add to Enquiries
GB00301 Bellinzoni Special Liquid for Polishing 675ml

Bellinzoni Granite Polishing Gel “Eureka”


Bellinzoni Granite Polishing Gel “Eureka”
Bellinzoni Granite Polishing Gel “Eureka”

Model: Bellinzoni Granite Polishing Gel “Eureka”

Manufacturer: Bellinzoni Italy


Bellinzoni Granite Polishing Gel “Eureka” is a new polishing gel, especially for polishing granite and gres quickly and easily, just using a single disc machine or a grinding-honing machine. It is possible to use it on smoothed materials, starting from grit 220 and above, or in alternative to tin oxide. It is a gel product, specifically designed to polish new granite and gres surfaces or to restore polish floors that lost shine and colour by high traffic. Bellinzoni Granite Polishing Gel “Eureka” does not contain lead.


 

Instruction for Use:

Wash the floor thoroughly using a single-disc machine equipped with appropriate disk, in order to eliminate all dirt, residues of old waxes and treatments (we recommend to use our Ultrastripper), rinse very well and dry up with a vacuum.

Pour a small quantity (around 30 gr) of Granite Polishing Gel “Eureka directly on the floor, under the natural fibre disk, dampen slightly and then work the product with the single disc machine (speed 150-400 rpm, minimum 30 Kg weight) or a polishing-grinding machine over around 1-2 m2 of floor. Pour water in case the gel dries up too quickly during operation. Distribute the product evenly and keep on working the surface until Granite Polishing Gel “Eureka is dried, until desired polish is obtained.

In case of very porous materials, treatment shall be repeated a second time. Afterwards wash and rinse with water and an alkaline substance (soda, bicarbonate or our Ultrastripper detergent) in order to eliminate residues of product and neutralize residual acidity

 

Suggestion for Use:

  • In case of very porous materials it could be necessary apply a second coat.
  • Deep cleaning of the floor before treatment is recommended.
  • If the machine becomes hard to use because of the friction between the machine and the stone, causing high heating of the floor, spray clean water directly on the floor.
  • Before use read the recommendations printed on the tin carefully.
  • Perform a preliminary test before use.

 

Application on surfaces:

Granite and gres surfaces

 

Coverage:

With 1 Litre of Granite Polishing Gel “Eureka” is possible to treat 20-30 m2

Product Documentation:

Granite Polishing Gel Technical.pdf


Code Description Unit Add to Enquiries
GB01101 Bellinzoni Granite Polishing Gel 1Lt 1LT

Bellinzoni Marble Polishing Gel “Eureka”


Bellinzoni Marble Polishing Gel “Eureka”
Bellinzoni Marble Polishing Gel “Eureka”

Model: Bellinzoni Marble Polishing Gel “Eureka”

Manufacturer: Bellinzoni Italy


Bellinzoni Marble Polishing Gel “Eureka” is a new polishing gel, especially for polishing marbles and calcareous materials quickly and easily, just using a single disc machine or a grinding-honing machine. It is possible to use it on smoothed materials, starting from grit 400 and above, or in alternative to polishing powders. It is a gel product, specifically designed to polish new marbles surfaces or to restore polish floors that lost shine and colour by high traffic. Bellinzoni Marble Polishing Gel “Eureka”  does not contain lead.


 

Instruction for Use:

Wash the floor thoroughly using a single-disc machine equipped with appropriate disk, in order to eliminate all dirt, residues of old waxes and treatments (we recommend to use our Ultrastripper), rinse very well and dry up with a vacuum.

Pour a small quantity (around 30 gr) of Marble Polishing Gel “Eureka” directly on the floor, under the natural fibre disk, dampen slightly and then work the product with the single disc machine (speed 150-400 rpm, minimum 30 Kg weight) or a polishing-grinding machine over around 1-2 m2 of floor. Pour water in case the gel dries up too quickly during operation. Distribute the product evenly and keep on working the surface until Marble Polishing Gel “Eureka” is dried, until desired polish is obtained.

In case of very porous materials, treatment shall be repeated a second time. At the end wash and rinse with water and an alkaline substance (soda, bicarbonate or our Ultrastripper detergent) in order to eliminate residues of product and neutralize residual acidity.

 

Suggestion for Use:

  • In case of very porous materials it could be necessary apply a second coat.
  • Deep cleaning of the floor before treatment is recommended.
  • If the machine becomes hard to use because of the friction between the machine and the stone, causing high heating of the floor, spray clean water directly on the floor.
  • Before use read the recommendations printed on the tin carefully.
  • Perform a preliminary test before use.

 

Application on surfaces:

Marble and calcareous stones surfaces

 

Coverage:

With 1 Litre of Marble Polishing Gel “Eureka” is possible to treat 20-30 m2

Product Documentation:

Marble Polishing Gel Technical.pdf


Code Description Unit Add to Enquiries
GB01201 Bellinzoni Marble Polishing Gel 1Lt 1LT

Bellinzoni Porcelain / Gres Polishing Gel “Eureka”


Bellinzoni Porcelain / Gres Polishing Gel “Eureka”
Bellinzoni Porcelain / Gres Polishing Gel “Eureka”

Model: Bellinzoni Porcelain / Gres Polishing Gel “Eureka”

Manufacturer: Bellinzoni Italy


Bellinzoni Porcelain Polishing Gel “Eureka” is a new polishing gel, especially for polishing granite and gres quickly and easily, just using a single disc machine or a grinding-honing machine. It is possible to use it on smoothed materials, starting from grit 220 and above, or in alternative to tin oxide. It is a gel product, specifically designed to polish new granite and gres surfaces or to restore polish floors that lost shine and colour by high traffic. Bellinzoni Porcelain Polishing Gel “Eureka” does not contain lead.

 


 

Instruction for Use:

Wash the floor thoroughly using a single-disc machine equipped with appropriate disk, in order to eliminate all dirt, residues of old waxes and treatments (we recommend to use our Ultrastripper), rinse very well and dry up with a vacuum.

Pour a small quantity (around 30 gr) of Porcelain Polishing Gel “Eureka directly on the floor, under the natural fibre disk, dampen slightly and then work the product with the single disc machine (speed 150-400 rpm, minimum 30 Kg weight) or a polishing-grinding machine over around 1-2 m2 of floor. Pour water in case the gel dries up too quickly during operation. Distribute the product evenly and keep on working the surface until Porcelain Polishing Gel “Eureka is dried, until desired polish is obtained.

In case of very porous materials, treatment shall be repeated a second time. Afterwards wash and rinse with water and an alkaline substance (soda, bicarbonate or our Ultrastripper detergent) in order to eliminate residues of product and neutralize residual acidity

 

Suggestion for Use:

  • In case of very porous materials it could be necessary apply a second coat.
  • Deep cleaning of the floor before treatment is recommended.
  • If the machine becomes hard to use because of the friction between the machine and the stone, causing high heating of the floor, spray clean water directly on the floor.
  • Before use read the recommendations printed on the tin carefully.
  • Perform a preliminary test before use.

 

Application on surfaces:

Porcelain and Gres surfaces

 

Coverage:

With 1 Litre of Porcelain Polishing Gel “Eureka” is possible to treat 20-30 m2


Code Description Unit Add to Enquiries
GB01301 Bellinzoni Porcelain / Gres Polishing Gel 1Lt 1LT

Bellinzoni Quartz / Resin Polishing Gel “Eureka”


Bellinzoni Quartz / Resin  Polishing Gel “Eureka”
Bellinzoni Quartz / Resin Polishing Gel “Eureka”

Model: Bellinzoni Quartz / Resin Polishing Gel “Eureka”

Manufacturer: Bellinzoni Italy


Bellinzoni Quartz / Resin Polishing Gel “Eureka” is a new polishing gel, especially for polishing quartz and resin quickly and easily, just using a single disc machine or a grinding-honing machine. It is possible to use it on smoothed materials, starting from grit 220 and above, or in alternative to tin oxide. It is a gel product, specifically designed to polish new quartz and resin surfaces or to restore polish floors that lost shine and colour by high traffic. Bellinzoni Quartz / Resin Polishing Gel “Eureka” does not contain lead.


 

 

Instruction for Use:

Wash the floor thoroughly using a single-disc machine equipped with appropriate disk, in order to eliminate all dirt, residues of old waxes and treatments (we recommend to use our Ultrastripper), rinse very well and dry up with a vacuum.

Pour a small quantity (around 30 gr) of Quartz / Resin Polishing Gel “Eureka directly on the floor, under the natural fibre disk, dampen slightly and then work the product with the single disc machine (speed 150-400 rpm, minimum 30 Kg weight) or a polishing-grinding machine over around 1-2 m2 of floor. Pour water in case the gel dries up too quickly during operation. Distribute the product evenly and keep on working the surface until Quartz / Resin Polishing Gel “Eureka is dried, until desired polish is obtained.

In case of very porous materials, treatment shall be repeated a second time. Afterwards wash and rinse with water and an alkaline substance (soda, bicarbonate or our Ultrastripper detergent) in order to eliminate residues of product and neutralize residual acidity

 

Suggestion for Use:

  • In case of very porous materials it could be necessary apply a second coat.
  • Deep cleaning of the floor before treatment is recommended.
  • If the machine becomes hard to use because of the friction between the machine and the stone, causing high heating of the floor, spray clean water directly on the floor.
  • Before use read the recommendations printed on the tin carefully.
  • Perform a preliminary test before use.

 

Application on surfaces:

Quartz and resin surfaces

 

Coverage:

With 1 Litre of Quartz / Resin Polishing Gel “Eureka” is possible to treat 20-30 m2

 


Code Description Unit Add to Enquiries
GB08301 Bellinzoni Quartz / Resin Polishing Gel 1Lt 1LT

Bellinzoni Marble Polishing Powder Supercristal


Bellinzoni Marble Polishing Powder Supercristal
Bellinzoni Marble Polishing Powder Supercristal

Model: Bellinzoni Marble Polishing Powder Supercristal

Manufacturer: Bellinzoni Italy


Description:

Bellinzoni Marble Polishing Powder Supercristal is used as a final step in achieving the high reflectivity finish that is seen on polished marble tiles and slabs. To be used with water and a buffing pad to get excellent results.


 

Instruction for Use:

  1. Spread Bellinzoni Marble Polishing Powder Supercristal on the floor manually in a circle, approximately a couple of square metres where single-disc machine will be used. Position the machine equipped with a natural fibre disc on the Bellinzoni Marble Polishing Powder Supercristal powder on the floor.
  2. With solution tank water control, wet the floor with water before turning on the floor machine. Add SuperCristal powder or water as necessary to maintain watery slurry. If a water solution tank is not used, wet a small area with clean water and sprinkle Bellinzoni Marble Polishing Powder Supercristal. Turn on the floor machine and work water and SuperCristal powder into slurry. Rotation of the machine may splatter the slurry, so take care to protect adjoining areas of carpet, wood and walls. Use the soft white floor maintenance pad for the application of this product on the stone.
  3. Work areas of no more than 1-2 square meters at a time. DO NOT ALLOW THE SLURRY TO DRY ON THE FLOOR AT ANY TIME.
  4. After running the floor machine over the area 3 or 4 times, use 16” or 18” window squeegee and pull across the area to check result. When a high polish in this area has been achieved, move the slurry with the squeegee to the next area to be polished.
  5. Rinse the floor with clean water and make sure all Bellinzoni Marble Polishing Powder Supercristal slurry is removed from the surface and grout joints.
  6. Repeat polishing process using the same slurry by adding water or Bellinzoni Marble Polishing Powder Supercristal as needed, until the entire area to be polished is completed.
  7. Wash the floor thoroughly with clean water and neutral detergent and leave it to dry. When the floor is dry, buff with clean and dry white floor maintenance pad.

 

Suggestion for Use:

  • Take care during use of the product because could burn the marble
  • Single disc machine must run maximum 175-200rpm, with a minimum weight of 45kg with solution tank, water feed and driver; 16”-17” white floor maintenance pad is required.
  • Read instruction on labels before use carefully.

 

Application on surfaces:

Marble and terrazzo.

 

Coverage:

For polishing of marble and granite polished, with 1 kg of product is possible to treat 40/50 m2 in dependence of the floor situation.

Product Documentation:

Marble Polishing Powder Supercristal Technical.pdf


Code Description Unit Add to Enquiries
GB01401 Bellinzoni Marble Polishing Powder Supercristal 1kg 1kg

Bellinzoni Crystallizer One


Bellinzoni Crystallizer One
Bellinzoni Crystallizer One

Model: Bellinzoni Crystallizer One

Manufacturer: Bellinzoni Italy


Bellinzoni Crystallizer One for the base crystallization of natural calcareous floors, terrazzo and resin marble. Bellinzoni Crystallizer One hardens the surface giving a long-lasting polish, similar to the polish obtained with conventional factory polisher. The liquid formula and the easy “one step job” allows to reduce working time and avoid eventual grinding of the floor; Bellinzoni Crystallizer One is perfect for crystallization and maintenance of big areas floors, like commercial centres, airports, etc.



Instructions for use:

Wash the floor thoroughly (we recommend using Bellinzoni LEM-3)

For badly damaged floors and very stubborn dirt you can try our degreasing cleaner Ultra Stripper.

Rinse the floor well (traces of old wax or grease must be completely removed)

Put Crystallizer One in a sprayer and spray evenly on the surface to be treated. Pass a single disc polish machine (175-200RPM) equipped with steel wool or white buff pad and slowly keep working until dry. Crystallizer One will create a thermos-chemical reaction while drying the surface. After treatment we suggest our Special Liquid Wax for Polishing to increase and protect the polish.

 

 

Suggestion for use:

  • After washing the floor, let it dry thoroughly to avoid and residues.
  • For white and light marbles we suggest using a white buff pad.
  • We suggest treating 1-3m2 at a time.
  • Avoid dripping Crystallizer One on the floor.
  • Make sure there is no left over residue of Crystallizer One on the floor.
  • Before use read the recommendations printed on the tin carefully.

 

Application on surfaces:

Marble, compact/agglomerate marble, agglomerate and engineered stone, terrazzo, resin marble, travertine and calcareous stone.

 

Yield:

With 1kg of Crystallizer One it is possible to treat from 30-40m2 of floor. Coverage depends on the condition of the floor and the type of material. 

Product Documentation:

Crystallizer One Technical.pdf


Code Description Unit Add to Enquiries
GB01001 Bellinzoni Crystallizer One 1lt 1LT

Bellinzoni Crystallizer Vetro-Glass


Bellinzoni Crystallizer Vetro-Glass
Bellinzoni Crystallizer Vetro-Glass

Model: Bellinzoni Crystallizer Vetro-Glass

Manufacturer: Bellinzoni Italy


It is now easy to renew a long-lasting sheen and to harden the surfaces of marble and stone agglomerates without using wax or resin. Just use Bellinzoni VETRO-GLASS crystallizer. A thermo-chemical reaction known as “crystallisation” is obtained by the use of a single-disc polishing-machine which lets the calcium carbonate (a natural marble component) to be dissolved by mild acids and mixed with vitrifying agents produces a shiny and extremely hard surface that looks like glass. Porosities are completely sealed, and the floor becomes much more resistant to traffic.


 

Instructions for use:

Wash the floor thoroughly (we recommend using Bellinzoni LEM-3)

For badly damaged floors and very stubborn dirt you can try our degreasing cleaner Ultra Stripper.

Rinse the floor well (traces of old wax or grease must be completely removed)

Put Crystallizer Vetro-Glass in a sprayer and spray evenly on the surface to be treated. Pass a single disc polish machine (175-200RPM) equipped with steel wool or white buff pad and slowly keep working until dry. Crystallizer Vetro-Glass will create a thermos-chemical reaction while drying the surface. After treatment we suggest our Special Liquid Wax for Polishing to increase and protect the polish.

 

 

Suggestion for use:

  • After washing the floor, let it dry thoroughly to avoid and residues.
  • For white and light marbles we suggest using a white buff pad.
  • We suggest treating 1-3m2 at a time.
  • Avoid dripping Crystallizer Vetro-Glass on the floor.
  • Make sure there is no left over residue of Crystallizer Vetro-Glass on the floor.
  • Before use read the recommendations printed on the tin carefully.

 

Application on surfaces:

Marble, compact/agglomerate marble, agglomerate and engineered stone, terrazzo, resin marble, travertine and calcareous stone.

 

Yield:

With 1kg of Crystallizer Vetro-Glass it is possible to treat from 30-40m2 of floor. Coverage depends on the condition of the floor and the type of material.

 

Product Documentation:

Crystallizer Vetro-Glass Technical.pdf


Code Description Unit Add to Enquiries
GB00901 Bellinzoni Crystallizer Vetro-Glass 1lt 1LT

Bellinzoni Ager Enhancer Vieux


Bellinzoni Ager Enhancer Vieux
Bellinzoni Ager Enhancer Vieux

Model: Bellinzoni Ager Enhancer Vieux

Manufacturer: Bellinzoni Italy


Marble and mankind have been joined in history for centuries. Old villas and ancient castles stand as witnesses to the beauty of marble. With the use of antique finish Bellinzoni Ager Enhancer Vieux even in a modern house full of modern appliances, we can enjoy the traditional because Bellinzoni Ager Enhancer Vieux lends the marble a warm and noble appearance, enhancing the colour beauty and quality. What nature has produced over centuries can now be reproduced in a few minutes, thanks to antique finish Bellinzoni Ager Enhancer Vieux.


 

Instructions for use:

After antiquing the stone using traditional ways (Tumbled, Sand blasted, flamed etc…) or with new technology products. Apply the product evenly on clean cloth and dry surface. Let it dry for 3 to 4 hours. To get more shine it is suggested to buff using a dry clean cloth, with fine steel wool or brush. For automatic polishing it is possible to use an electric tool with felt disc. Floor application can be made using a single disc machine equipped with red disc or steel wool. For regular maintenance use detergent Bellinzoni LEM 3 for cleaning and Bellinzoni Liquid Wax to renew the polish

 

 

Suggestion for use:

  • To facilitate penetration of the wax into the material we suggest warming the slab, this procedure will open the porosities, letting the wax penetrate deeply.
  • If application is made on the floor, be careful because it may become slippery. Slipperiness will decease after periodical washing.
  • To delay dry time of the wax dilute the product 30% with turpentine.
  • Do not apply on synthetic materials. (Plastic, rubber, linoleum etc…)
  • Before use read the recommendations printed on the tin carefully.

 

Application on surfaces:

Marble, granite, travertine, slate tiles and agglomerate natural stones

 

Yield:

For polishing of marble and granite polished greater than 800# grit and with 1 kg of wax it is possible to treat 25-30 m2. In case of calcareous stone, limestone, sans stone, polished concrete with grit higher than 800# it is possible to treat 15-20m2

 

Product Documentation:

Ager Enhancer Vieux Technical.pdf


Code Description Unit Add to Enquiries
GB00601 Bellinzoni Ager Enhancer Vieux 725ml 725ml

Bellinzoni Antislip Polish AS11


Bellinzoni Antislip Polish AS11
Bellinzoni Antislip Polish AS11

Model: Bellinzoni Antislip Polish AS11

Manufacturer: Bellinzoni Italy


Description:

Liquid wax based on natural and synthetic waxes, thanks to its special formula to reduce slipperiness of marble, granite, terrazzo and ceramic floors. It gives a brilliant warm sheen and reduces the slipperiness of the treated surface at the same time.

 


 

Instruction for Use:

Wash the floor (We recommend using Bellinzoni LEM-3).

For very old or very dirty floors we recommend Bellinzoni Ultra Stripper (Floor must be free from old waxes and grease).

After washing, rinse very well and let it dry (you can use a vacuum to remove liquid) and wait until completely dry. Once the floor has dried proceed to apply the wax with a damp cloth. Let the wax dry avoiding contact. Polish energetically with a dry cloth or floor polishing machine. The result will be a brilliant floor. Periodical floor treatment must be done with water and out AS22 ant slip clean and polish. Repeat the application periodically

 

 

Suggestion for Use:

  • The longer the wax stays on the floor prior to buffing the better the final result will be.
  • We suggest always diluting the wax in order to avoid build-up on the floor.
  • Product for indoor use.
  • It is suggested to make different rest treatment with different dilutions in order to reach the best anti slip. This procedure is necessary because different stone have different absorption.
  • Follow the instruction printed on the tin carefully
  • This product needs maintenance.

 

Application on surfaces:

Marble, granite, terrazzo engineered stone, resin marble and most natural stones.

 

Coverage:

1 litre of anti-slip can treat 40/50 m2 in dependence of the floor situation.

Product Documentation:

Antislip Polish AS11 Technical.pdf


Code Description Unit Add to Enquiries
GB05101 Bellinzoni Antislip Polish AS11 1lt 1LT